E-bike conversion kit supplier guidance – UK cycle industry response
The Bicycle Association
The Association of Cycle Traders
11th November 2026
The Bicycle Association and the Association of Cycle Traders, the two trade bodies representing the UK cycle industry, note the publication yesterday by the Office for Product Safety and Standards of regulatory guidance for suppliers of e-bike conversion kits.
The UK cycle industry is not opposed to e-bike conversion kits as such, and we are not calling for a ban on the sale of road legal e-bike conversion kits. We recognise that some consumers may decide to use a conversion kit to enjoy the benefits of electrically assisted cycling based on an existing pedal cycle. But this guidance in our view falls short of enabling consumers to make a proper informed choice when it comes to e-bike conversion kits.
We are grateful to OPSS to have had the opportunity to contribute to the development of this guidance, and for some changes which have been made to reflect our input. And we do hope that the guidance will be helpful to assist UK market authorities in enforcement against irresponsible suppliers of unsafe conversion kits.
However, we are disappointed that in several key respects, our input on behalf of the UK cycle industry has not been accepted.
We are concerned that the resulting shortcomings mean that this guidance:
- Fails to ensure that consumers and retailers are properly informed of the safety risks, responsibilities, potential liabilities and legal consequences they incur when fitting a conversion kit to a pedal cycle to create an e-bike.
- Risks legitimising the sale of non road legal e-motorbike conversion kits, when these should have been declared as intrinsically unsafe. It is surprising that OPSS takes this approach at a time when illegal use of non-road legal e-motorbikes, many created via conversion kits, is a major concern for communities and police forces UK-wide.
- Causes confusion through a regulatory view contrary to long established international understanding. This risks legitimising without proper customer safeguards a ‘short cut’ route to the creation of less safe e-bikes based on pedal cycle frames, forks and braking systems which were never designed or tested for e-bike use. This in turn undermines the investments made in testing, product safety and regulatory compliance by reputable suppliers of complete e-bikes, who thoroughly test complete e-bikes, as e-bikes, to demanding international standards..
In particular, we are concerned that:
- The published guidance covers only the duties of conversion kit suppliers, without consideration of the risks, responsibilities and potential liabilities of people, businesses or organisations who fit kits and thereby manufacture e-bikes.
A person or business fitting a conversion kit becomes the manufacturer of the resulting e-bike in law but will normally be unable to satisfy the legal responsibilities this involves. We believe customers should be made aware of this pre-sale.
This guidance for kit suppliers also offers no new clarity for retailers who fit kits, so the existing BA/ACT advice for retailers who may be considering fitting e-bike conversion kits still applies. This references previously published OPSS guidance which states that "If you supply parts and convert a bike or a scooter into an e-bike or e-scooter, you are legally responsible for its safety, and may be liable for any damage caused by any defect."
- It is also a material consideration for purchasers that fitting an e-bike conversion kit will normally void any manufacturer’s warranty on the pedal cycle to which it is fitted. The guidance fails to require kit suppliers to state this clearly pre-transaction.
- The guidance assumes that it is generally possible for an e-bike created by adding a drive system to a pedal cycle to be 'safe' (as defined in product safety regulation), and that it is sufficient for the kit supplier to specify which type and condition of pedal cycle may be used. But no pedal cycle’s frame, fork and brakes were designed or tested for use as an e-bike, and certainly not for use as an e-motorbike. So safety when any pedal cycle is used as an e-bike after conversion can never be assumed. Nor should safety rely on consumers (even if guided by supplier instructions) making difficult or impossible evaluations of a particular pedal cycle's suitability for safe conversion.
We believe that it should as a minimum be mandatory to inform the customer pre-sale that fitting an e-bike kit to any pedal cycle means exceeding its original structural design and safety capabilities, and that structural and performance safety margins will be reduced in e-bike use. This would ensure that any potential conversion kit purchase is made in full awareness of these risks.
- For e-bike conversion kits which do not meet the EAPC criteria (max assistance speed 25 km/h, max continuous rated motor power 250 W) the structural safety and braking questions are even more concerning. Such kits effectively add an e-motorbike drive system to a pedal cycle frame, fork and braking system which were never designed for use as an e-motorbike.
It should at the very least be mandatory for sellers to inform customers prominently pre-sale if an e-bike created via one of these kits will not be road legal.
But we believe that OPSS should have used this guidance to go further by declaring such kits intrinsically unsafe, rather than legitimising their sale by including non-road-legal kits in the scope of this guidance but omitting any safety warning about structural and braking risks. This recent court case suggests that non road legal conversion kits can indeed be considered intrinsically unsafe in law, and a seller was fined on this basis.
- The guidance suggests that e-bike conversion kits be considered “machinery”, inappropriately referencing a clause in the regulations which official guidance confirms is intended only for vehicle-mounted equipment with specific functions, such as truck-mounted loading cranes, tail lifts and similar devices. This view contradicts published guidance and goes against long established international understanding, both in the cycle industry and among conformity assessment bodies and test labs.
The established understanding and natural interpretation of the regulations is that an e-bike conversion kit is a drive system, and hence in regulatory terms “partly completed machinery”, rather than ‘machinery’.
OPSS’s in our view mistaken interpretation risks undermining clarity about product safety roles and responsibilities in managing the extra risks involved when creating an e-bike from a pedal cycle, and international confusion.
Again, the UK cycle industry is not opposed to e-bike conversion kits as such. We recognise that they have the potential to enable people to enjoy the benefits of electrically assisted cycling using an existing pedal cycle. The industry is not calling for a ban on the sale of road legal e-bike conversion kits (although it should be illegal to sell non-road-legal conversion kits, as they are intrinsically unsafe).
And we do support conversion kit supplier responsibilities being very clearly set out, to help with enforcement against irresponsible sellers of unsafe kits.
But by covering only supplier responsibilities in this guidance, OPSS in our view risks creating a strong and misleading impression that there are no extra risks or responsibilities worth considering as a result of fitting and using e-bike conversion kits to vehicles originally designed and tested only as pedal cycles.
We urged OPSS to also address in this guidance the regulatory position of complete e-bikes created from kits, and to clarify for example how it is possible (if it is possible at all) for the creator of a converted e-bike to comply with legal requirements for e-bikes which OPSS itself enforces (and which responsible suppliers of complete e-bikes invest heavily in satisfying, for their users' safety).
If it had addressed these issues, this guidance could have ensured that potential kit purchasers are enabled by mandatory pre-purchase information to make a fully informed choice between either:
- a fully safety-tested complete e-bike from an accountable supplier (such as those listed on the industry's trust mark scheme, E-Bike Positive, which also lists responsible e-bike retailers)
- or the conversion kit route, which involves the consumer recognising and accepting that there are intrinsic risks to kit-created e-bikes which can never be properly covered off by the conversion kit supplier, that any original bike warranty will be void, and that the kit fitter takes full legal responsibility for the safety of the completed e-bike.
It could also have ensured that both individuals and businesses such as retailers have real clarity about the responsibilities they take on when creating an e-bike by fitting a kit.
As the trade bodies representing responsible suppliers and retailers in the UK cycle industry, the Bicycle Association and Association of Cycle Traders urge OPSS to urgently reconsider publication of this guidance in its current form.
ENDS